How to Hide Joints on 90-Degree Wood Corners

Learn to conceal corner joints with router-cut beads, shadow lines, quarter round, square blocks, and a rabbeted wrap.

In this video, Gary Striegler shares several ways to turn a 90-degree outside corner in wood without cutting a miter. He covers a router-cut beaded corner, a table saw and beading bit profile that hides the joint in a shadow line, an offset corner finished with quarter round or a square block, and a rabbeted wrap that is flush-trimmed so the joint sits back from the edge. The techniques work for cabinetry, wainscot, and trim carpentry. For more, visit Carpentry with Gary Striegler on YouTube.

VIDEO TRANSCRIPT:

Hey, I’m Gary Striegler, and one of the most challenging things I have to do when I’m building cabinets, or putting wainscot on a wall, is turning a 90-degree outside corner with wood.

There are bits that make locking miters and such. To be honest, I’m sure there are people who can make those work very well, but they just don’t work well for me. So I want to share three or four different options for turning an outside corner and getting a great-looking joint.

A beaded corner is cut with two router passes

The first one I really, really like is this beaded corner, which I made using this router bit right here. You make one pass with the router up on edge, and then you make the second pass with the router like that. You get a really nice corner.

A shadow line hides the joint

I’ve shaded this area dark. If I remove that amount of wood, I get a joint like this, where the shadow line right here hides the joint. I’ll pull it back a little so you can see it better. Again, the joint is hidden in that shadow line, so you get a really good-looking joint at the corner without having to cut a miter.

A beading bit profile conceals the joint the same way

This one is similar. If you take a beading bit, where you’ve got a rounded-over corner and two shoulders, I’ve again made dark the parts you would remove with a table saw. Here’s a piece that’s had that removed. When I bring this in, I end up with a really nice joint, and the joint is hidden right in here. Let me see if I can stand that up.

That’s simply sawing out that part and bringing the other piece in. Now I get a really good joint that I don’t see, because it’s concealed in part of the profile.

An offset corner with quarter round is the one I use most on cabinetry

Here’s one I use a whole lot, especially on cabinetry. If you just put two pieces together (I put that block in there to hold it), you leave a 3/4 by 3/4 offset. Then I can come back in and lay a piece of wood in there. This is a piece of quarter round, and hopefully there’s enough contrast that you can see I’ve got a really good-looking corner without doing much work. This piece of trim just makes a transition.

I could also put a piece of quarter round in there, and that’s another very nice transition. If I wanted something a little more contemporary, I could put in this 5/8 by 5/8 block. Here I took a chamfer bit and eased the edge. I darkened it, but that gives you a different look.

A rabbeted wrap is the simplest version of the joint

Maybe the simplest way to make that joint is what I’ve got on this end. I cut a rabbet a little over 3/4 inch wide to wrap the corner, leaving about a quarter inch of wood right here. I glued it up, and after the glue dried, I took a flush-trim bit and trimmed it back flush. You can see the offset here. The joint is now concealed about a quarter inch back from the edge.

I could also set the bit a little shallower and use a round-over bit, and now I’ve got a nicely rounded-over joint that’s super hard to see.

Concealing the joint is easier than fitting a miter

Those are several ways to handle what’s a challenging part of any project: making an outside corner, whether it’s a trim carpentry project or a cabinetry project. You hide the joint, and you get a great joint that is a lot easier to make than trying to get two 45s to come together.

Sign up for our eNewsletters
Get the latest news and updates